• ARC433 Series Si10-416_B ARC433B46, B47 ECONO ON/OFF TEMP POWERFUL MODE SWING QUIET MOLD PROOF SENSOR CANCEL TIMER Remote Controllers. • Si10-416_B ARC433 Series 1. Download free millenium star atlas pdf software pc.

Signal transmitter 2. Display It displays the current settings. (In this illustration, each section is shown with all its displays ON for the purpose of explanation.) 3. ECONO button 4.

POWERFUL button 5. TEMPERATURE adjustment buttons 6.

• Si10-416_B ARC433 Series 5. ARC433 Series 5.1 Preparation Before Operation To set the batteries 1. Slide the front cover to take it off. Set two dry batteries (AAA).

DAIKIN ROOM AIR CONDITIONER OPERATION MANUAL MODELS. Never allow the air conditioner or remote controller to get. Contact your Daikin Dealer. • The remote. How to Use Air-Conditioning Remotes in Japan. Nothing is more frustrating than trying to decipher the buttons on an air-conditioner remote control or heater thermostat. The Japanese air-conditioner remote I translated here is a Daikin model. I hope this helps. I may add other photos and translations here in.

Set the front cover as before. Position + and – correctly! ATTENTION About batteries •.

• ARC433 Series Si10-416_B To operate the remote controller • To use the remote controller, aim the transmitter at the indoor unit. If there is anything to block signals between the unit and the remote controller, such as a curtain, the unit will not operate. • Si10-416_B ARC433 Series ATTENTION About remote controller • Never expose the remote controller to direct sunlight. • Dust on the signal transmitter or receiver will reduce the sensitivity. Wipe off dust with soft cloth. • Signal communication may be disabled if an electronic- starter-type fluorescent lamp (such as inverter-type lamps) is in the room.

• ARC433 Series Si10-416_B To set the clock 1. Press “CLOCK button”. Is displayed. Press “TIMER setting button” to set the clock to the present time. Holding down “ ” or “ ” button rapidly increases or decreases the time display.

• Si10-416_B ARC433 Series 5.2 AUTO • DRY • COOL • HEAT • FAN Operation The air conditioner operates with the operation mode of your choice. From the next time on, the air conditioner will operate with the same operation mode. To start operation 1. • ARC433 Series Si10-416_B To change the temperature setting 4. Press “TEMPERATURE adjustment button”. DRY or FAN mode AUTO or COOL or HEAT mode Press “ ” to raise the temperature and press “ ” The temperature setting is to lower the temperature. Not variable.

• Si10-416_B ARC433 Series NOTE Note on HEAT operation • Since this air conditioner heats the room by taking heat from outdoor air to indoors, the heating capacity becomes smaller in lower outdoor temperatures. If the heating effect is insufficient, it is recommended to use another heating appliance in combination with the air conditioner. • ARC433 Series Si10-416_B 5.3 Adjusting the Airflow Direction You can adjust the airflow direction to increase your comfort. To adjust the horizontal blade (flap) 1. Press “SWING button ”.

• “ ” is displayed on the LCD and the flaps will begin to swing. • Si10-416_B ARC433 Series To 3-D Airflow Press the “SWING button ” and the “SWING button ”: the “ ” and “ ” display will light up and the flap and louvers will move in turn. To cancel 3-D Airflow Press either the “SWING button ”. • ARC433 Series Si10-416_B 5.4 COMFORT AIRFLOW Operation To start COMFORT AIRFLOW operation 1.

Press “COMFORT AIRFLOW button”. • The flap position will change, preventing air from blowing directly on the occupants of the room.

• “ ” is displayed on the LCD. • Si10-416_B ARC433 Series 5.5 POWERFUL Operation POWERFUL operation quickly maximizes the cooling (heating) effect in any operation mode.